Fiberglass Chopped Strand Mat

Fiberglass Chopped Strand Mat (CSM) is made from randomly distributed chopped glass fibers held together with a compatible binder. With a suitable binder and grade, CSM can wet out effectively with compatible polyester or vinyl ester resins and conform to complex mould shapes. CSM is commonly used in hand lay-up and moulding processes for tanks, pipes, panels, automotive parts and general FRP components where uniform reinforcement and economical laminate build-up are required. Available specifications should be selected according to the resin system, process and final mechanical requirements.

Powder-Bound Chopped Strand Mat

The powder-bound type consists of randomly distributed chopped glass strands bonded into a sheet with a powder binder. The supplied product information describes E-glass strands approximately 50 mm long with silane-based sizing. The sizing supports the glass/resin interface, while the powder binder holds the dry mat together for handling and mould placement.

A suitable grade offers good drapability, wet-through and air release during impregnation. These characteristics help the operator consolidate layers over curves and corners. Wet-out speed, dry-mat handling strength and resin demand depend on the selected grade, binder and resin system.

Powder and Emulsion Binder Options

VIP Global Co. can source both powder-bound and emulsion-bound chopped strand mat. Emulsion-bound mat is sometimes called the “oily” type in the local market; its technical English designation is emulsion-bound CSM. The powder-grade reference specifications below do not apply automatically to the emulsion type.

Unsaturated polyester and vinyl ester are common resin systems for suitable CSM grades. Epoxy and phenolic compatibility must be confirmed in the technical data sheet for the exact product. Binder type alone is not sufficient to establish compatibility or processing suitability.

Processing and Typical Applications

Hand lay-up is a common application. Selected grades may also be suitable for compression moulding, filament winding and continuous laminating. CSM contributes randomly oriented reinforcement and laminate build-up; the final laminate thickness and mechanical performance depend on area weight, layer count, resin content, other reinforcements and curing conditions.

  • FRP tanks, pipe components and appropriately designed corrosion-resistant laminates
  • Boat hulls, decks and other marine components
  • Panels, sanitaryware and automotive body components
  • Cooling towers, building components and selected sports equipment

Resistance to water or chemicals is a property of the complete laminate system. Resin selection, barrier-layer design, glass type and service conditions must be evaluated for the intended application.

Powder-Grade Reference Specifications

The following values are transcribed from the supplied powder-mat product information. They are supplier-reference specifications, subject to confirmation for the grade and shipment offered by VIP Global Co.

Reference codeGlass typeBinderArea weight (g/m²)Roll net weight (kg)Reported roll length (m)*Binder content (%) — as supplied
CSM-130E-glassPowder130 ± 5%302218 ≤
CSM-225E-glassPowder225 ± 5%301284.5 ≤
CSM-300E-glassPowder300 ± 5%30963.5 ≤
CSM-450E-glassPowder450 ± 5%30653 ≤
CSM-600E-glassPowder600 ± 5%30482.7 ≤

*Roll length depends on roll width and area weight. These reported lengths are reference values, not lengths for every width. The source image contains an unclear width unit and an inconsistent width entry; roll width and binder-content limits must be confirmed from the original supplier data sheet before ordering.

Emulsion-Bound Chopped Strand Mat

Emulsion-bound CSM is the second binder option available through VIP Global Co., locally referred to as the “oily” type. Chopped glass strands are distributed randomly and held together by an emulsion binder, giving the dry sheet cohesion for unwinding, cutting and mould placement. The supplied product description specifies approximately 50 mm chopped strands with silane-based sizing.

This type is used in hand lay-up and, for suitably specified grades, other low-pressure moulding or continuous laminating processes. Suitable grades offer conformability, resin impregnation and air release for FRP tanks, marine components, panels, sanitaryware and other moulded parts. Select the grade for the intended resin and process rather than assuming identical behaviour to powder-bound mat.

Emulsion-Grade Reference Specifications

The following values are taken from the supplied emulsion-mat information and are subject to confirmation for the product quoted.

Reference codeGlass typeBinderArea weight (g/m²)Roll net weight (kg)Reported roll length (m)*Binder content (%) — as supplied
CSM-225E-glassEmulsion225 ± 5%301285.5 ≤
CSM-300E-glassEmulsion300 ± 5%30964.5 ≤
CSM-450E-glassEmulsion450 ± 5%30963 ≤

*Length depends on roll width and area weight. The 96 m length for the 450 g/m² grade is reproduced from the supplied reference; reported lengths apply to the corresponding roll width. Roll widths and binder-content limits are confirmed in the selected product’s technical data sheet.

Storage and Product Selection

Keep rolls dry, protected from moisture and in their original packaging until use. Follow the selected manufacturer’s storage conditions and shelf-life guidance. Specify binder type, resin system, manufacturing process, area weight, roll width, quantity and delivery destination when requesting a quotation.

Supply and Delivery by VIP Global Co.

VIP Global Co. works closely with leading chopped strand mat manufacturers in Iran and the Middle East. We support orders in a range of quantities with competitive pricing, short sourcing lead times and coordinated supply and shipping services. The selected grade, available quantity, delivery schedule and commercial terms are confirmed with each quotation.

Request a quotation for powder or emulsion chopped strand mat

Technical Selection Guide

Parameter

Technical guidance

Reinforcement structure

Non-woven mat of randomly distributed chopped glass strands held together by a binder.

Binder options

Powder or emulsion binder; select the exact grade for the resin system and manufacturing process.

Nominal area weight (g/m²)

Examples include 225, 300, 450, 600 and 900 g/m². These are nominal mat weights, not roving tex values. Availability depends on the selected product.

Resin compatibility

Select grades approved for unsaturated polyester or vinyl ester. Epoxy or phenolic use requires explicit compatibility confirmation in the selected grade's technical data sheet.

Processing

Hand lay-up; selected grades also suit filament winding, compression moulding or continuous laminating. Confirm suitability for the intended process.

Typical applications

FRP tanks, pipes, panels, boat components, sanitaryware, automotive parts and building components, subject to laminate design.

Grade-specific quality parameters

Area-weight tolerance, moisture content, binder/organic content and dry-mat breaking force must be confirmed from the selected grade's TDS. Dry-mat breaking force is not cured-laminate strength.

Roll dimensions and packaging

Specify roll width, length or net weight and packaging when requesting a quotation; dimensions vary by product and supplier.

Selection and supply confirmation

General selection guide, not a product-specific TDS or stock list. Confirm grade, binder, resin, area weight, roll dimensions, quantity and destination before ordering.